Key Takeaway
- In CLO Virtual Fashion's CLO, Pattern Drafter | Auto POM & Grading drafts a selected pattern type from entered measurements, and changing a Point of Measure (POM) length updates the parametric pattern without starting over.
- You can enter full measurement values for every size or define increments between sizes in Pattern Drafter, and edit the resulting grading rules later.
- After modifying a 2D pattern, running a fresh simulation lets you inspect tightness, pressure, stress, and stretch percentage across four garment Fit Maps.
Revising a collar stand on a woven shirt or adjusting chest ease on an outerwear block often forces you to redraw linked seams by hand just to keep armholes and hemlines aligned. When you need to test those revisions on a digital avatar before cutting fabric, the way your software handles measurement changes determines whether a spec update takes seconds or requires rebuilding the draft. In CLO Virtual Fashion's CLO, changing a POM length inside Pattern Drafter updates the parametric pattern without starting over and preserves its parametric relationships. For shared review, CLO-SET is a separate platform where teams can share and discuss 3D garments.
Parametric Pattern Drafting and 3D Review in CLO
Adjusting a spec sheet measurement after an initial fit session should not require reconstructing the base block from scratch. When you draft a garment using Pattern Drafter | Auto POM & Grading in CLO, the software generates the selected pattern type from your entered measurements and creates 2D POMs only for those defined measurements.
If a sleeve length or waist circumference needs to change during development, altering that POM length updates the parametric pattern while keeping the parametric relationships across the piece intact. Pattern Drafter can also align pattern dimensions to the size of a CLO avatar. Because the workspace combines 2D pattern creation and editing with 3D garment simulation, you can check how a pattern adjustment affects the garment.
CLO and Browzwear VStitcher Pattern Workflow
Apparel teams evaluating 2D drafting, measurement-driven updates, and 3D size review can compare how CLO and Browzwear VStitcher structure these tasks.
| Capability | CLO | Browzwear VStitcher |
|---|---|---|
| Measurement-Driven Pattern Edits | Changing a POM length in Pattern Drafter updates the parametric pattern without starting over and preserves parametric relationships; modify drafts via Pattern Drafter > Edit or the Edit POM tool. | In VStitcher 2026.3, Target & Apply Changes reshapes a piece from a POM target on the base size only (enabled for Enterprise and Teams SSO accounts); it solves the whole piece at once so changing one Target can alter other measurements, and if all Targets cannot be reached, the pattern remains unchanged. |
| 2D Drafting and 3D Workspace | Supports 2D pattern creation and editing alongside 3D garment simulation to check how adjustments affect the garment. | Supports garment work in both 2D drafting and 3D draping environments for visual refinement. |
| Size Grading and Multi-Size POMs | Grading Review lets teams simulate each graded size and compare garment and avatar views; if pattern geometry changes, the affected size requires re-simulation. | Fits garments on customizable 3D avatars and grades across sizes; Apply Changes works on the base size while other sizes update automatically through grading, and the Sizes tab displays read-only POM values for every size with size filtering and optional Diff columns. |
Sources: CLO Virtual Fashion, Browzwear, and the Browzwear Help Center.
How a tool recalculates geometry affects daily pattern engineering. When you need to tweak an existing draft in CLO, you modify the pattern through Pattern Drafter > Edit or use the Edit POM tool. If you change pattern geometry while comparing graded sizes in Grading Review, you run the simulation again on the affected size to inspect the updated drape.
Grading a CLO Pattern from Size Measurements
Scaling an activewear tight or a structured jacket across a size range works differently depending on whether your spec sheet lists complete pattern measurements per size or step-by-step increments. Pattern Drafter accommodates both approaches by grading patterns either from full measurement values entered for each individual size or from grading increments between sizes, producing editable results.
You are not locked into the initial setup once the base draft is generated. Using the grading tool, you can edit the grading rules even after the initial Pattern Drafter configuration is complete. To verify how those rules behave across the size run, the software supports reviewing fit by size on screen so you can spot grading issues.
Reviewing 3D Avatar Fit in CLO After Pattern Edits
Checking whether a revised armhole binds or a waistband digs in requires looking at how the updated 2D pieces behave under tension on a 3D body. When you edit a 2D pattern while simulation is active, the simulation stops, allowing you to simulate the updated garment again to review the revision.
In the Avatar Editor, choose bust circumference, underbust circumference, or weight to set overall width, and total height, HPS height, or inseam to set height. Use Set Details to select additional measurements, then enter their values. Refine localized proportions with Shape settings and save the size configuration as an .AVS file.
Once the garment is simulated on the avatar, distinguish between surface dimension checks and tension analysis:
- Use Garment Measure to check dimensions on the simulated garment and Fit Maps to inspect tightness, stretch, stress, and pressure.
- Strain Map displays garment stretch as a percentage, while Stress Map shows stress on the garment.
- Fit Map indicates tightness and Pressure Map shows the pressure the garment exerts on the avatar.
- In CLO, Strain Map’s Fabric Mode calculates an adjustable wearable stretch limit from each fabric’s physical properties.
Examining these maps after re-simulating a modified pattern lets you verify whether an added centimeter at the hip or chest actually relieves excess stretch for the specific textile in your file.
FAQ
How does software automate pattern creation from entered measurements?
In CLO, Pattern Drafter | Auto POM & Grading drafts the selected pattern type directly from the measurement values you enter and generates 2D POMs for those defined measurements. If you need to adjust a spec later, changing a POM length updates the parametric pattern without starting over.
Can I customize digital avatar proportions to match specific fit targets before testing a garment?
Yes. Use the Avatar Editor to set overall proportions, select additional measurements through Set Details, and refine localized areas with Shape settings. Save the measurement configuration as an .AVS file, or save the avatar itself as an .AVT file.
How can I check if a fabric is stretching beyond its wearable limit during a 3D fit review?
CLO provides four Fit Maps—Strain Map (showing stretch as a percentage), Stress Map, Fit Map, and Pressure Map. Fit Maps use fabric physical properties to determine and apply the maximum wearable strain rate.